-- Low read noise, high quantum efficiency and faster acquisition address different experimental needs, with each specification tied to its operating conditions.
In cold-atom experiments and fluorescence microscopy, a scientific camera may have little light and little time to work with. Researchers need enough signal to distinguish neighboring targets or follow a changing sample, while preserving the spatial information needed for analysis.
The Revealer Qbit 5505 sCMOS camera addresses those demands through a back-illuminated sensor and separate readout modes for faint signals and faster acquisition. Its effective array measures 2,560 by 2,048 pixels, about 5.24 megapixels, with a pixel pitch of 5.5 micrometers. The combination provides a platform for low-light imaging in which sensitivity, spatial sampling and recording speed can be matched to the experiment.
Published product figures list read noise of about 0.3 electrons, expressed as a median, in the 14-bit single-photon mode. That mode runs at 9 frames per second. Lower read noise can help retain differences between faint signals and background when only a few photoelectrons are generated in each pixel during an exposure. It is particularly relevant to slowly changing targets or experiments whose repetition cycle allows that acquisition rate.
Faster modes operate under different conditions. Through CoaXPress, the camera reaches up to 120 fps in 14-bit high-gain rolling-shutter mode and up to 240 fps at full resolution in 12-bit high- or low-gain global-shutter mode. Listed high-gain read noise is 0.75 electrons rms in rolling-shutter mode and 1.0 electrons rms in global-shutter mode. The minimum-noise and maximum-speed figures describe separate working configurations.
Those choices matter in cold-atom, ion-trap and optical-tweezer experiments, where fluorescence intensity and target position must be recorded together. The array provides spatial information for observing multiple sites. A relatively stationary target may suit the single-photon mode; repeated readout at a higher rate requires a fresh assessment of signal and background in the selected faster mode.

Figure. Cold-ion fluorescence imaging reference from the supplied Revealer Qbit 5505 materials, showing three bright spots against a dark background.
Photon collection presents another part of the problem. Back illumination reduces obstruction from front-side wiring, and the Qbit 5505 has a stated peak quantum efficiency of 95 percent at 520 nanometers. At that wavelength, a high proportion of photons reaching the sensor can be converted to photoelectrons. In a green-fluorescence experiment with limited light, this can increase the useful signal collected during a fixed exposure.
The peak value does not describe every emission wavelength. Atomic transitions, fluorescent probes and spectrometer bands may fall elsewhere on the response curve, while lenses, windows and filters further affect the light reaching the sensor. Shorter exposures or lower excitation power can be considered when the resulting signal-to-noise ratio meets the experiment’s requirements.
Spatial sampling also needs context. At total magnifications of 10 and 60, the 5.5-micrometer pixels correspond to nominal sample-plane sampling intervals of about 0.55 and 0.092 micrometers. These are sampling intervals; numerical aperture, wavelength and aberrations also constrain spatial resolution. Spreading a target’s signal across more pixels can increase the contribution of read noise to its integrated measurement.
For live cells, single particles and sparsely labeled samples, high quantum efficiency and low read noise act at different stages of signal acquisition. Faster cellular processes or particle trajectories may call for a higher frame rate, provided each frame still contains enough photoelectrons for localization, segmentation or tracking. Exposure duration affects motion blur, and trigger timing links the camera to illumination or experimental control pulses. Rolling-shutter operation also requires attention to differences in exposure timing between rows.
The camera provides USB 3.2 Gen 2 and dual CXP-12 interfaces, with full-frame, region-of-interest and pixel-binning options. USB supports routine computer connections, while CoaXPress accommodates higher data throughput. Continuous acquisition depends on the frame grabber, memory transfers, buffering and storage keeping pace with the camera. Actual frame rate, dropped frames and trigger response are therefore part of the system assessment.
Thermoelectric cooling helps suppress thermally generated dark signal. Its contribution during longer exposures needs to be assessed with dark frames at the intended temperature and exposure time. Recording conversion gain, the linear operating range and correction settings helps keep measurements comparable across acquisition conditions.
Other applications involve different limits. Astronomical lucky imaging uses short exposures, frame selection, registration and stacking to reduce some effects of atmospheric disturbance. A faster mode is useful only if individual frames contain adequate signal. Raman and materials-emission measurements require the camera response to match the target spectral band; spectral resolution also depends on the slit, dispersive optics and pixel sampling.
Across these experiments, the Revealer Qbit 5505 sCMOS camera offers configurable detection conditions for different photon budgets and time scales. Its contribution to low-light imaging depends on linking the selected mode with the optics, timing and calibration, so weak optical signals become measurements with defined noise, spatial sampling and temporal reference.
Contact Info:
Name: Harrison Shawn
Email: Send Email
Organization: HF Agile Device Co., Ltd.
Website: http://www.revealerhighspeed.com
Release ID: 89210317

Google
RSS